You need to create a settings file for each custom panel and you will find a Savage Cub one already in the settings folder. Instrument Panel now supports multiple panels in case you decide to build a Savage Cub panel for example instead of a Cessna panel. Not all instruments have manual controls. See individual instruments for pins used. Each rotary encoder is connected to two BCM GPIO pins (+ ground on centre pin). On Raspberry Pi you can configure hardware Rotary Encoders for each instrument. Packages will be created under the main folder. When you build the solution it will automatically download AllegroĪs it is specified in nfig. Load instrument-panel.sln into Visual Studio 2022 Community Edition. It has been completely rewritten and updated to use Allegro5. This program was heavily inspired by Dave Ault and contains original artwork by him. If you just want to test the instrument panel on the same host where FS2020 is running leave the IP address as 127.0.0.1 and it will connect to the local host.īlaine Leckett made his own instrument panel using my software and he has a very good build video here: You do this by editing the settings file and updating the Data Link Host IP address. Each panel must be configured to point to the host where data-link is running. You can run as many instrument panels as you like. The instrument panel connects to the instrument-data-link over your network and receives the data at regular intervals so that the instruments can be drawn with up-to-date values. The companion program runs on the same host as MS FS2020 and collects all the data required by the instrument panel. It requires the companion program from here: You can see it running on a Raspberry Pi 4 here: Īnd in action on a VFR flight with VATSIM from Gatwick to London City Airport here: It can run on either a PC or a Raspberry Pi. This program is designed to run on a separate computer to the one running FS2020 but you can just run it on a different monitor if you wish. IntroductionĪn instrument panel for MS FlightSim 2020. Ready-built releases for Windows 圆4 and Raspberry Pi 4 can be found by clicking on the Releases section on the right of this readme. Nano settings/instrument-panel.json (change HOST to the IP address of your PC) You can then install Instrument Panel on Rapsberry Pi by doing the following: Quick Start on Raspberry Piįollow the instructions above to download Instrument Data Link on Windows. If you want to use the Savage Cub panel instead of the default Cessna panel or you want to define multiple panel layouts see section "Custom Panels" below. It will also dim when you are flying and enter the pause menu. Note: There is a screensaver feature so the instrument panel will appear dim until you run FS2020 and select where you are flying from. Now double-click instrument-panel.exe to run it. 192.168.0.1 - You can find the correct address of your host by running a command prompt on the host machine and running ipconfig, then scroll back and look for the first "IPv4 Address" line. Edit settings/instrument-panel.json and in the "Data Link" section change the IP address of the "Host" to the address where FS2020 is running on your local network, e.g. To run instrument-panel on a different PC, unzip instrument-panel to a folder on the new PC. If you then press Escape to exit the program the settings will be saved and it will run on the same monitor next time. Press M to switch the display to a different monitor so it's not on the same monitor as FS2020. If you are running it on the same PC as FS2020 the default settings are correct so just double-click instrument-panel.exe to run it. Unzip instrument-panel into its own folder. Unzip instrument-data-link into its own folder and double-click instrument-data-link.exe to run it. Link: Latest release of Instrument Data Link for Windows Link: Latest release of Instrument Panel for Windows You can also run the display on a PC (the same one running FS2020 if you wish) but you won't have the knob inputs then although you can still use the knobs in the FS2020 cockpit and the changes will immediately be reflected on the instrument panel display. The knobs are connected to the GPIO pins of the same Raspberry Pi that is running the display. The instrument panel is running on a single 24" monitor with plywood placed in front of it and holes cut out for each instrument. MICROSOFT FLIGHT SIMULATOR 2020 - INSTRUMENT PANEL
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |